National 3000HP Drilling Rig
National 1625M 3000HP SCR Drilling Rig. Complete with Top Drive, Catwalk and more, Rig rebuilt in 2004, last drilled in 2015. Offered As-Is Where-Is. Inventory and Spec Sheet in link below Inventory Spec Sheet Message us below for Pricing Read More
Cardwell Workover Rig
Cardwell 350HP 4-Axle Carrier Double/Triple Workover Rig. Tooled Out and Ready-To-Work Rig. SPECS: Cardwell 4-Axle Carrier, Double Drum Drawworks, 96’ mast with 180,000# hook load raise and scope derrick, Detroit 8V71N 318HP with Allison CLBT446-2 Transmission, 9/16” sandline w/8” brakes on drum, 7/8” drilline w/10” brakes on drum, Oil Saver Pump. No tubing or rod […] Read More
Kenworth 170K Snubbing Unit
Low Mile and Low Hour Kenworth T800 170K Rig Assist Snubbing Unit, Great Deal on this one! SPECS: 39,600 Miles, 10,300 Hours | Paccar MX 12.9L Diesel Engine | Eaton Fuller 8LL Transmission | Haul max Suspension 20k fronts, 46k Rears w/21k Drop Axles | 425/65r22.5 Front Tires, Rears 11r24.5 | Double Framed 170K Snubbing […] Read More
Forum FH80 Iron Roughneck
Remanufactured Forum FH80 Floorhand Iron Roughneck, rebuilt by Ranger Oilfield Products, Excellent Condition and Priced to Sell SPECS: Size Range 4”OD-8 1/2”OD* / 101.6mm OD-215.9mm OD • Make-Up Torque 65,000 ft-lbs / 88,300 Nm • Break-Out Torque 80,000 ft-lbs. / 108,500 Nm Message us below for Pricing Read More
Atlas Copco RD20 III
Atlas Copco 750HP Hydraulic Top Drive Drilling Rig, very nice mobile rig and priced to sell! SPECS: SN 21052, W/ INGERSOLL RAND 1250/350 AIR COMPRESSOR, HYDS P/B CAT C27 DIESEL ENG, 30,000# PULLDOWN, 120,000# PULLBACK CAPACITY, 52′ RNG 3 TOWER, FMC TRIPLEX MIST PUMP P/B HYD MOTOR, DOWNHOLE LUBRICATOR, SHOCK SUB, BRADEN UTILITY WINCHES, MTD […] Read More
OCO 5K Choke Manifold
Rebuilt O.C.O. 5K Choke Manifold complete with Control Panel. This manifold is setup w/10 each 3-1/8″ 5K valves and 7 each 2-1/16″ 5K valves with 2 manual adjustable chokes and 1 hydraulic choke (Swaco style), all the valves/chokes are MCM Oil Tools. This choke manifold is mounted on a Heli-portable skid. Message us below for […] Read More
NOV ST100 Iron Roughnecks
Two (2) NOV ST100 Iron Roughnecks. Both in Great Condition, Package DEAL for both or can be purchased separately. SPECS: Max Torque 100,000 FT LBS Make-Up, 120,000 FT LBS Breakout, Tubular Dia 3 1/2″ to 9 3/4″ Message us below for Pricing Read More
Cameron 500 Workover Rig
Cameron 500HP 5-Axel Double Drum Workover Rig, With Detroit Series 60 14L Power, 104′ 250,000# Mast, 42″ X 12″ Main Drum, 38″ X 8″ Sand Drum, Single Cab. Great Condition and Priced to Move! Offered As-Is Where-Is Message us below for Pricing Read More
RMI 500HP Workover Rig
RMI 500HP 5-Axle Carrier Workover Rig, 96’ Derrick Rated at 215,000#, Tooled-Out and Ready to Work. Refurbished in 2010 by NOV, total rig hours as of September 2024 · 12,618.2 hours. Full specs and additional photos in links below RMI Workover Rig Specs Additional Photos Message us below for Pricing Read More
SLB Twin Cementing Unit
Refurbished Schlumberger SLB CPS-361 Double Pump Cementing Unit mounted on Skid. SPECS: 2x Engines 8V71 Diesel 8 Cylinders, 2x Allison HT 750 DR Transmissions, 6 Speed, 2x Gardner Denver/ Dowell PG-05 Power ends, GD Fluid ends, Front Pump 5,500 PSI (3.75in Plunger) Rear Pump 10k PSI (5in Plunger), 4x Centrifugal Pumps for mixing and recirculation […] Read More
Southwest Oilfield CTU
Un-Used Surplus “NEW” Southwest Oilfield Coil Tubing Unit. 80K Injector Heads, C15 power pack with approximately 4 hour. This unit has been stored inside, Holds 18,000’ of 1.5” and has 16,000’ of New Surplus 1.5” pipe. Ready-To-Work Unit! Scroll down page for run-out video, see link below for additional photos. Additional Photos Message us below for […] Read More
NOV ST-80 Iron Roughneck
Rebuilt NOV ST-80 Iron Roughneck. Pipe Capacity of 4 1/4″ to 8 1/2″ with Make-up/Break-out Torque of 60,000/80,000 ft-lbs. Message us below for Pricing Read More